View IR3629_8688711.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IR3629/IR3629a mpbf 11/29/2007 high frequency synchronou s pwm buck controller with power good output description the IR3629/IR3629a is a pwm controller designed for high performance synchronous buck dc/dc applications. the IR3629/IR3629a drives a pair of external n-mosfets using a fixed 600khz (300khz a version) switching frequency allowing the use of small external components. the output voltage can be precisely regulated using the internal 0.6v reference voltage for low voltage applications. protection such as pre-bias startup, hiccup current limit and thermal shutdown provide the required system level security in the event of fault conditions. features internal 600khz oscillator (300khz a version) operates with single 5v or 12v supply programmable over current protection hiccup current limit using mosfet r ds(on) sensing precision reference voltage (0.6v) programmable soft-start programmable pgood output pre-bias start-up thermal protection 12-lead mlp package fig. 1: typical application circuit ordering information pkg package pin parts parts t&r desig description count per tube per reel orientation m IR3629/IR3629ampbf 12 122 ------- m IR3629/IR3629amtrpbf 12 -------- 3000 figure a applications distributed point-of-loads embedded systems storage systems ddr applications graphics cards computing peripheral voltage regulators general dc-dc converters data sheet no. pd94726 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 package information 12-lead mlpd, 3x4mm 2 ja = 30 o c/w * jc = 2 o c/w 4 3 2 1 9 10 11 12 hdrv v cc ocset pgnd ldrv ss/sd gnd comp 5 v c 8 fb exposed pad 7 vsns 6 pgood *exposed pad on underside is connected to a copper pad through vias for 4-layer pcb board design absolute maximum ratings (voltages referenced to gnd) vcc supply voltage ................................................ -0.5v to 16v vc supply voltage .. -0.5v to 30v pgood -0.5v to 16v fb, comp, ss .... -0.3v to 3.5v ocset 10ma agnd to pgnd ... -0.3v to +0.3v storage temperature r ange ................. .................... -65 c to 150 c operating juncti on temperature range ................... -40 c to 150 c esd classification .. jedec, jesd22-a114 moisture sensitivity level . jedec level 2 @ 260 o c caution: stresses beyond those listed under absolute maxi mum rating may cause permanent damage to the device. these are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational secti ons of the specifications is not impl ied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 block diagram fig. 2: simplified block di agram of the IR3629/IR3629a 3 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 pin description pin name description 1 pgood power good status pin. output is open collector. connect a pull up resistor from this pin to vcc. 2 vcc this pin provides biasing voltage for the internal blocks of the ic. it also biases the low side driver. a minimum of 0.1uf, high frequency capacitor must be connected from this pin to power ground. 3 ldrv output driver for the low side mosfet 4 pgnd power ground. this pin serves as a separate ground for the mosfet drivers and should be connected to the systems power ground plane. 5 hdrv output driver for the high side mosfet 6 vc this pin powers the high side driver and must be connected to a voltage higher than bus voltage. a minimum of 0.1uf, high frequency capacitor must be connected from this pin to power ground. 7 vsns pgood sense pin 8 fb inverting input to the error amplifier. this pin is connected directly to the output of the regulator via resistor divider to set the output voltage and provide feedback to the error amplifier. 9 comp output of the error amplifier. 10 gnd signal ground for internal reference and control circuitry. 11 ss/sd soft start / shutdown. this pin provides user programmable soft-st art function. connect an external capacitor from this pin to ground to set the start up time of the output voltage. the converter can be shutdown by pulling this pin below 0.3v. 12 ocset current limit set point. a resistor from this pin to drain of the l ow side mosfet will set the current limit threshold. 4 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 recommended operating conditions parameter sym test condition min typ max units accuracy feedback voltage v fb 0.6 v 0 o cIR3629, c load =1.5nf 15 25 v cc supply current (dynamic) i cc(dynamic) IR3629a, c load =1.5nf 15 19 v c supply current (static) i c(static) ss=0v, no switching 4.5 7 IR3629, c load =1.5nf 17 25 v c supply current ( dynamic) i c(dynamic) IR3629a, c load =1.5nf 10 15 ma under voltage lockout v cc -start-threshold v cc _uvlo(r) supply ramping up 4.0 4.2 4.4 v cc -stop-threshold v cc _uvlo(f) supply ramping down 3.7 3.9 4.1 v cc -hysteresis v cc _hys supply ramping up and down 0.15 0.25 0.3 v c -start-threshold v c _uvlo(r) supply ramping up 3.1 3.3 3.5 v c -stop-threshold v c _uvlo(f) supply ramping down 2.85 3.05 3.25 v c -hysteresis v c _hys supply ramping up and down 0.15 0.2 0.25 v oscillator IR3629a 270 300 330 frequency f s IR3629 540 600 660 khz ramp amplitude v ramp note3 1.25 v min duty cycle d min fb=1v 0 % IR3629, note3 80 min pulse width d min(ctrl) IR3629a , note3 160 ns IR3629, fb=0.5v 71 max duty cycle d max IR3629a, fb=0.5v 78 % electrical specifications unless otherwise specified, these specification apply over v cc =v c =12v, 0 o c IR3629/IR3629a mpbf 11/29/2007 parameter sym test condition min typ max units error amplifier input bias current i fb1 ss=3v -0.1 -0.5 input bias current i fb2 ss=0v 20 35 50 source/sink current i(source/sink) 50 70 90 a transconductance gm 1000 1300 1600 mho soft start/sd soft start current i ss ss=0v 15 20 28 a shutdown output threshold sd 0.25 v over current protection ocset current i ocset 15 20 26 hiccup current i hiccup note3 3 a hiccup duty cycle hiccup(duty) i hiccup / i ss , note3 15 % power good vsns lower trip point vsns(trip) vsns ramping down 0.35 0.38 0.41 v hysteresis pgood(hys) 15 27.5 40 mv pgood output low voltage pg(voltage) i pgood =4ma 0.25 0.5 v input bias curent i sns 0 0.3 1 a thermal shutdown thermal shutdown threshold td note3 140 thermal shutdown hysteresis td(hys) note3 20 o c output drivers lo, drive rise time tr(lo) cl=1.5nf, see fig 3 30 60 hi drive rise time tr(hi) cl=1.5nf, see fig 3 30 60 lo drive fall time tf(lo) cl=1.5nf, see fig 3 30 60 hi drive fall time tf(hi) cl=1.5nf, see fig 3 30 60 dead band time tdead see fig 3 10 50 100 ns note2: cold temperature performance is guaranteed via correlation using statistical quality control. not tested in production. note3: guaranteed by design but not tested in production. 9v 2v 9v 2v high side driver (hdrv) low side driver (ldrv) tr tf deadband h_to_l deadband l_to_h tr tf fig. 3: definition of rise/fall time and deadband time 6 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 typical operating characteristics vfb(mv) 597.0 597.5 598.0 598.5 599.0 599.5 600.0 600.5 601.0 -40-20 0 20406080100120 temp[oc] [mv] iss(ma) 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 -40 -20 0 20 40 60 80 100 120 temp[oc] [ua] icc(static)(ma) 6.0 7.0 8.0 9.0 10.0 11.0 12.0 -40-20 0 20406080100120 temp[oc] [ma] ic(static)(ma) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 -40 -20 0 20 40 60 80 100 120 temp[oc] [ma] transconductance (gm)[mmho] 1.0 1.1 1.1 1.2 1.2 1.3 1.3 1.4 1.4 1.5 -40-20 0 20406080100120 temp[oc] [mmho] iocset(ua) 18.0 18.5 19.0 19.5 20.0 20.5 21.0 21.5 22.0 -40 -20 0 20 40 60 80 100 120 140 temp[oc] [ua] frequency (khz)(IR3629) 570.0 575.0 580.0 585.0 590.0 595.0 600.0 605.0 610.0 615.0 -40 -20 0 20 40 60 80 100 120 140 temp[oc] [khz] frequency(khz)(IR3629a) 270.0 275.0 280.0 285.0 290.0 295.0 300.0 305.0 310.0 -40-20 0 20406080100120140 temp[oc] [khz] 7 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 circuit description theory of opeartionintroduction the IR3629/29a is a voltage mode pwm synchronous controller and operates with a fixed 600khz (300khz for IR3629a) switching frequency, allowing the use of small external components. the output voltage is set by a feedback pin (fb) and the internal reference voltage (0.6v). these are the two inputs to the error amplifier. the error signal between these two inputs is amplified and it is compared to a fixed frequency linear sawtooth ramp and generates fixed frequency pulses of variable duty-cycle (d) which drivers n-channel external mosfets. the internal oscillator circuit uses an on-chip capacitor to set the switching frequency. the IR3629/29a operates with single input voltage from 4.5v to 12v allowing an extended operating input voltage range. the current limit is programmable and uses on- resistance of the low-side mosfet, eliminating the need for an external current sense resistor . under-voltage lockout the under-voltage lockout circuit monitors the two input supplies (vcc and vc) and ensures that the mosfet driver outputs remain in the off state whenever the supply voltage drops below set thresholds. lockout occurs if vc or vcc fall below 3.3v and 4.2v respectively. normal operation resumes once vc and vcc rise above the set values. thermal shutdown temperature sensing is provided inside the IR3629/29a. the trip threshold is typically set to 145 o c. when the trip threshold is exceeded, thermal shutdown discharges the soft start voltage and turns off both mosfets. thermal shutdown is not latched and automatic restart is initiated when the sensed temperature drops within the operating range. there is a 20 o c hysteresis in the thermal shutdown threshold. shutdown the output can be shutdown by pulling the soft- start pin below 0.3v. this can easily be done by using an external small signal transistor. during shutdown both mosfet drivers will be turned off. normal operation will resume by cycling the soft start pin. pre-bias startup the IR3629/29a is able to start up into pre- charged output, which prevents oscillation and disturbances of the output voltage. the output starts in asynchronous fashion and keeps the synchronous mosfet off until the first gate signal for control mosfet is generated. figure 4 shows a typical pre-bias condition at startup. depending on the system configuration, specific amount of output capacitors may be required to prevent discharging the output voltage. fig. 4: pre-bias startup vo time volt pre-bias voltage (output voltage before startup) power good the IR3629/29a provides an open collector power good signal which reports the status of the output. the output is sensed through the dedicated vsns pin. the power good threshold can be externally programmed using two external resistors. the power good comparator is internally set to 0.38v (typical). minimum pulse width the time required for turning on and off the high side mosfet is defined as minimum pulse width. to ensure that a reliable operation is achieved the following condition needs to be met: s in out on f v v t * (max) (min) < 8 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 soft-start the IR3629/29a has a programmable soft-start to control the output voltage rise and limit the inrush current during start-up. to ensure correct start-up, the soft-start sequence initiates when vcc and vc rise above their threshold and generate the power on ready (por) signal. the soft-start function operates by sourcing current to charge an external capacitor to about 3v. initially, the soft-start function clamps the output of error amplifier by injecting a current (35ua) into the fb pin and generates a voltage about 0.84v (35ux24k) across the negative input of error amplifier (see figure 5). the magnitude of the injected current is inversely proportional to the voltage at the soft-start pin. as the soft-start voltage ramps up, the injected current decreases linearly and so does the voltage at the negative input of error amplifier. when the soft-start capacitor voltage is around 1v, the voltage at the positive input of the error amplifier is approximately 0.6v. the output of the error amplifier will start increasing and generating the first pwm signal. as the soft-start capacitor voltage continues to rise up, the current flowing into the fb pin will keep decreasing. the feedback voltage increases linearly as the soft-start voltage ramps up. when soft-start voltage is around 2v the output voltage reaches the steady state and the injected current is zero. figure 6 shows the theoretical operating waveforms during soft-start. the output voltage start-up time is the time period when soft-start capacitor voltage increases from 1v to 2v. the start-up time will be dependent on the size of the external soft-start capacitor and can be estimated by: fig. 5: soft-start circuit for IR3629/29a fig. 6: theoretical operation waveforms during soft-start 20ua 40ua por error amp ss/sd fb comp 24k 0.6v 24k 3v soft-start voltage voltage at negative input of error amp voltage at fb pin current flowing into fb pin 40ua 0ua 0v 0.6v ? 0.96v 0.6v 0v 3v ? 2v ? 1v output of uvlo por for a given start-up time, the soft-start capacitor (nf) can be estimated as: v1 v2 c t a 20 ss start ? = ? )1 --( ms t a 20 c start ss ) ( * ? 9 35ua 35ua 0.84v downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 over-current protection the over current protection is performed by sensing current through the r ds(on) of the low- side mosfet. this method enhances the converters efficiency and reduces cost by eliminating a current sense resistor. as shown in figure 7, an external resistor (r set ) is connected between ocset pin and the drain of the low-side mosfet (q2) which determines the current limit set point. the internal current source develops a voltage across r set . when the low-side mosfet is turned on, the inductor current flows through the q2 and results in a voltage which is given by: the ocp circuit starts sampling current when the low gate drive is about 3v. the ocset pin is internally clamped during deadtime to prevent false trigging. figure 9 shows the ocset pin during one switching cycle. as shown, there is about 150ns delay to mask the deadtime. since this node contains switching noises, this delay also functions as a filter. fig. 7: connection of over current sensing resistor fig. 8: 3ua current source for discharging soft-start capacitor during hiccup l1 r set ir3624 ocset i ocset v out hiccup control q1 q2 an over-current is detected if the ocset pin goes below ground. this trips the ocp comparator and cycles the soft start function in hiccup mode. the hiccup is performed by charging and discharging the soft-start capacitor in a certain slope rate. as shown in figure 8, a 3ua current source is used to discharge the soft-start capacitor. the ocp comparator resets after every soft start cycle. the converter stays in this mode until the overload or short circuit is removed. the converter will automatically recover. ss1 / sd 20 28ua 3ua ocp )2 ) --( i (r ) r (i v l ds(on) ocset ocset ocset ? ? ? = 0 )i (r ) r (i v l ds(on) ocset ocset ocset = ? ? ? = )3 --( r i r i i onds ocset ocset critical l set )( ) ( ? = = fig. 9: ocset pin during normal condition ch1: inductor point, ch2:ldrv, ch3:ocset the value of r set should be checked in an actual circuit to ensure that the over-current protection circuit activates as expected. the IR3629 current limit is designed primarily as a disaster preventing, "no blow up" circuit, and does not operate as a precision current regulator. the critical inductor current can be calculated by setting: 20ua i ocset *r ocset blanking time deadtime clamp voltage 10 IR3629/29a downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 application information design example: the following example is a typical application for IR3629a. the application circuit is shown on page 18. output voltage programming output voltage is programmed by reference voltage and external voltage divider. the fb pin is the inverting input of the error amplifier, which is internally referenced to 0.6v. the divider is ratioed to provide 0.6v at the fb pin when the output is at its desired value. the output voltage is defined by using the following equation: when an external resistor divider is connected to the output as shown in figure 10. equation (4) can be rewritten as: for the calculated values of r 8 and r 9 see feedback compensation section. khz =f pple) voltage ri mv(output v a =i v.= v ) v,. v,( = v s o o o in 300 54 25 81 max 2 13 12 )4 --( r r 1 v v 9 8 ref o ? ?? ? ? ?? ? + ? = fig. 10: typical application of the IR3629a for programming the output voltage )5 --( v v v r r ref o ref 8 9 ? ?? ? ? ?? ? ? ? = soft-start programming the soft-start timing can be programmed by selecting the soft-start capacitance value. the start-up time of the converter can be calculated by using: where t start is the desired start-up time (ms). for a start-up time of 10ms, the soft-start capacitor will be 0.2uf. choose a ceramic capacitor at 0.22uf. vc supply for single input voltage to drive the high side switch, it is necessary to supply a gate voltage at least 4v greater than the bus voltage. this is achieved by using a charge pump configuration as shown in figure 11. this method is simple and inexpensive. the operation of the circuit is as follows: when the lower mosfet is turned on, the capacitor (c1) is pulled down to ground and charges, up to v bus value, through the diode (d1). the bus voltage will be added to this voltage when the upper mosfet turns on in the next cycle, and providing supply voltage (vc) through diode (d2). vc is approximately: a capacitors in the range of 0.1uf is generally adequate for most applications. fast recovery diodes must be used to minimize the amount of charge fed back from the charge pump capacitor into v bus . the diodes need to be able to block the full power rail voltage, which is seen when the high-side mosfet is switched on. for low- voltage applications, schottky diodes can be used to minimize forward drop. l ir3624 d1 c1 vc hdrv q1 q2 c2 v bus d2 c3 v bus fig. 11: charge pump circuit to generate vc voltage ( ) )6 --( v v v 2 v 2d 1d bus c + ? ? ? )1 --( t a 20 c start ss * ? fb ir3624 v out r 9 r 8 IR3629a 11 IR3629/29a downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 input capacitor selection the ripple current generated during the on time of upper the mosfet should be provided by the input capacitor. the rms value of this ripple is expressed by: where: d is the duty cycle i rms is the rms value of the input capacitor current. io is the output current. for io=25a and d=0.15, the i rms =8.9a. ceramic capacitors are recommended due to their peak current capabilities, they also feature low esr and esl at higher frequency which enables better efficiency. however, for the large pulsing input current at full load, 2x270uf 16v os-con capacitors from sanyo are recommended, as well as 2x10uf 16v ceramic capacitors from murata. inductor selection the inductor is selected based on output power, operating frequency and efficiency requirements. a low inductor value causes large ripple current, resulting in the smaller size, faster response to a load transient but poor efficiency and high output noise. generally, the selection of the inductor value can be reduced to the desired maximum ripple current in the inductor . the optimum point is usually found between 20% and 50% ripple of the output current. for the buck converter, the inductor value for the desired operating ripple current can be determined using the following relation: where: )7 --( d 1 d i i o rms ) ( ? ? ? = in o v v d = s o in f 1 d t t i l v v ? = ? = ? ; ) ( i () ) --( fi v v v v l s in o o in 8 * ? ? ? = cycle duty d time on turn t frequency switching f current ripple inductor i voltage output v voltage input maximum v s o in = = = = = = if , then the output inductor will be: l 0.6uh the mpl104-0r6 from delta provides a compact, low profile inductor suitable for this application. output capacitor selection the voltage ripple and transient requirements determine the output capacitors type and values. the criteria is normally based on the value of the effective series resistance (esr). however the actual capacitance value and the equivalent series inductance (esl) are other contributing components. these components can be described as: since the output capacitor has a major role in the overall performance of the converter and determines the result of transient response, selection of the capacitor is critical. the IR3629a can perform well with all types of capacitor. as a rule, the capacitor must have low enough esr to meet output ripple and load transient requirements. the goal for this design is to meet the voltage ripple requirement in the smallest possible capacitor size. therefore a sp capacitor is selected due to large capacitance and small size. two of the panasonic sp-cap eefsx0d331xe (330uf, 2v, 6mohm) is a good choice. in this case, the esr dominates the output voltage ripple, equation (9) can be used to calculate the required esr for the specific voltage ripple. ) %( 40 o i i current ripple inductor i ripple voltage output v f c 8 i v esl l v v -(9) - esr i v v v v v l o s o l co in eslo l esro co eslo esro o = = = ?? ? ?? ? = = + + = * * * * )( )( )( )( )( )( 12 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 power mosfet selection the IR3629a uses two n-channel mosfets per channel. the selection criteria to meet power transfer requirements are based on maximum drain-source voltage (v dss ), gate-source drive voltage (v gs ), maximum output current, on- resistance r ds(on) , and thermal management. the mosfet must have a maximum operating voltage (v dss ) exceeding the maximum input voltage (v in ). the gate drive requirement is almost the same for both mosfets. a logic-level transistor can be used and caution should be taken with devices at very low gate threshold voltage (v gs ) to prevent undesired turn-on of the complementary mosfet, which results in a shoot-through current. the total power dissipation for mosfets includes conduction and switching losses. for the buck converter the average inductor current is equal to the dc load current. the conduction loss is defined as: the r ds(on) temperature dependency should be considered for the worst case operation. this is typically given in the mosfet datasheet. ensure that the conduction losses and switching losses do not exceed the package ratings or violate the overall thermal budget. for this design, the irf6712 is selected for control fet and irf6715 is selected for the synchronous fet. these devices provide low on resistance in a directfet package. the mosfets have the following data: the conduction losses will be: p con =1.05w at io=25a. the switching loss is more difficult to calculate, even though the switching transition is well understood. the reason is the effect of the parasitic components and switching times during the switching procedures such as turn-on / turn- off delays and rise and fall times. the control mosfet contributes to the majority of the switching losses in a synchronous buck converter. the synchronous mosfet turns on under zero voltage conditions, therefore, the turn on losses for synchronous mosfet can be neglected. with a linear approximation, the total switching loss can be expressed as: where: v ds(off) = drain to source voltage at the off time t r = rise time t f = fall time t = switching period i load = load current the switching time waveforms is shown in figure12. from irf6712 data sheet: tr = 11ns tf = 19ns these values are taken under a certain test condition. for more details please refer to the irf6712 data sheet. by using equation (10), we can calculate the switching losses. p sw =1.35w at io=25a. the reverse recovery loss is also another contributing factor in control fet switching losses. this is equivalent to extra current required to remove the minority charges from the synchronous fet. the reverse recovery loss can be expressed as: (10) --- * * )( load fr offds sw i t tt v p + = 2 v ds v gs 10% 90% t d (on) t d (off) t r t f fig. 12: switching time waveforms cy g frequen : switchin f ery time verse : t e ery ch verse :q *f *tq p s rr rr srrrr qrr cov re re arg cov re re = 13 dependency re temperatu r d) (1 r i switch) (lower p d r i switch) (upper p ds(on) ds(on) 2 load cond ds(on) 2 load cond = ? ?? ? = = ?? ? = = ? ? ? v v m ? r nc v,q v gs ds(on) g ds 10 @ 8.3 12 25 : (irf6712) controlfet = = = = v v m ? r nc v,q v gs ds(on) g ds 10 @ 3.1 40 25 : (irf6715) syncfet = = = = downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 feedback compensation the IR3629a is a voltage mode controller. the control loop is a single voltage feedback path including error amplifier and error comparator. to achieve fast transient response and accurate output regulation, a compensation circuit is necessary. the goal of the compensation network is to provide a closed-loop transfer function with the highes t 0db crossing frequency and adequate phase margin (greater than 45 o ). the output lc filter introduces a double pole, C 40db/decade gain slope above its corner resonant frequency, and a total phase lag of 180 o (see figure 13). the resonant frequency of the lc filter is expressed as follows: figure 13 shows gain and phase of the lc filter. since we already have 180 o phase shift from the output filter a lone , the system risks being unstable. the IR3629/29as error amplifier is a differential- input transconductance amplifier. the output is available for dc gain control or ac phase compensation. the error amplifier can be compensated either in type ii or type iii compensation. when it is used in type ii compensation the transconductance properties of the error amplifier become evident and can be used to cancel one of the output filter poles. this will be accomplished with a series rc circuit from comp pin to ground as shown in figure 14. this method requires the output capacitor should have enough esr to satisfy stability requirements. in general the output capacitors esr generates a zero typically at 5khz to 50khz which is essential for an acceptable phase margin. (11) --- c l 2 1 f o o lc ? ? = gain f lc 0db phase 0 f lc -180 frequency frequency -40db/decade fig. 13: gain and phase of lc filter the esr zero of the output capacitor expressed as follows: the transfer function (ve/vo) is given by: the (s) indicates that the transfer function varies as a function of frequency. this configuration introduces a gain and zero, expressed by: the gain is determined by the voltage divider and error amplifiers transconductance gain. first select the desired zero-crossover frequency (fo): use the following equation to calculate r3: where: v in = maximum input voltage v osc = oscillator ramp voltage f o = crossover frequency f esr = zero frequency of the output capacitor f lc = resonant frequency of the output filter r 8 and r 9 = feedback resistor dividers g m = error amplifier transconductance 1.28 = empirical number to compensate thermal, process variations and co mponents tolerances (12 ) --- c esr 2 1 f o esr * * ? = fig. 14: typeii compensation network and its asymptotic gain plot (13 ) --- sc c sr 1 r r r g sh 4 43 8 9 9 m + ? ?? ? ? ?? ? + = * * )( () [] (15) --- c r 2 1 f (14) --- r* r r r g sh 4 3 z 3 8 9 9 m * * * = ? ?? ? ? ?? ? + = ( ) s o esr o f 1/10 ~ 1/5 f and f f * > (15a ) --- * * * .*) (* * * m lc in esr o osc g r f v r r f f v r 9 2 9 8 3 281 + = ve v out v ref r 9 r 8 r 3 c 4 e/a f z h(s) db frequency gain(db) fb comp c pole 14 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 to cancel one of the lc filter poles, place the zero before the lc filter resonant frequency pole: using equations (15) and (16) to calculate c9. one more capacitor is sometimes added in parallel with c4 and r3. this introduces one more pole which is mainly used to suppress the switching noise. the additional pole is given by: the pole sets to one half of the switching frequency which results in the capacitor c pole : for a general solution for unconditional stability for any type of output capacitors, in a wide range of esr values we should implement local feedback with a compensat ion network (type iii). the typically used compensation network for voltage-mode controller is shown in figure 15. in such configuration, the transfer function is given by: the error amplifier gain is independent of the transconductance under the following condition: by replacing z in and z f according to figure 15, the transfer function can be expressed as: (16) --- c l 2 1 75 0 f f 75 f o o z lc z * * . % = = as known, the transconductance amplifier has a high impedance (current source) output, therefore, consideration should be taken when loading the error amplifier output. it may exceed its source/sink output current capability, so that the amplifier will not be able to swing its output voltage over the necessary range. the compensation network has three poles and two zeros and they are expressed as follows: cross over frequency is expressed as: c c c c r 2 1 f pole 4 pole 4 3 p + = * * * s s pole f c f r c * r* 1 * * 3 ? ? = 4 3 1 1 fig.15: compensation network with local feedback and its asymptotic gain plot in m fm o e z g 1 z g 1 v v + ? = ( ) [] ) (* * *) ( * ) ( )( 710 3 4 3 4 3 10 8 7 43 3 48 c sr 1 c c c c sr 1 r r sc 1 c sr 1 c c sr 1 sh + ?? ? ?? ? ? ?? ? ? ?? ? + + + + + + = 8 7 10 8 7 2z 4 3 1z 3 3 3 4 3 4 3 3p 7 10 2p 1p r c 2 1 r r c 2 1 f c r 2 1 f c r 2 1 c c c c r 2 1 f c r 2 1 f 0 f * * ) (* * * * * * * * * * ? + = = ? ? ?? ? ? ?? ? + = = = o o osc in 7 3 o c l 2 1 v v c r f * * * * * = (17) --- 1 z* g and 1 z* g in m f m > > > > v out v ref r 9 r 8 r 10 c 7 c 3 c 4 r 3 ve f z 1 f z 2 f p 2 f p 3 e/a z f z in frequency gain(db) h(s) db fb comp 15 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 based on the frequency of the zero generated by the output capacitor and its esr versus crossover frequency, the compensation type can be different. the table below shows the compensation types and location of the crossover frequency. the following design rules will give a crossover frequency approximately one-fifth of the switching frequency. the higher the band width, the potentially faster the load transient response. the dc gain will be large enough to provide high dc-regulation accuracy (typically -5db to -12db). the phase margin should be greater than 45 o for overall stability. detailed calculation of compensation type iii method a: ceramic f lc IR3629/IR3629a mpbf 11/29/2007 programming the current-limit the current-limit threshold can be set by connecting a resistor (r set ) from the drain of the low-side mosfet to the ocset pin. the resistor can be calculated by using equation (3). the r ds(on) has a positive temperature coefficient and it should be considered for the worst case operation. this resistor must be placed close to the ic, place a small ceramic capacitor from this pin to ground for noise rejection purposes. layout consideration the layout is very important when designing high frequency switching converters. poor layout will affect noise pickup and can cause a good design to perform with less than expected results. start to place the power components, making all the connection in the top layer with wide, copper filled areas. the inductor, output capacitors and the mosfets should be as close to each other as possible. this helps to reduce the emi radiated by the power traces due to the high switching currents through them. place input capacitor very close to the drain of the high-side mosfet, to reduce the esr replace the single input capacitor with two parallel units. the feedback part of the system should be kept away from the inductor and other noise sources. the critical bypass components such as capacitors for vcc and vc should be close to the respective pins. it is important to place the feedback components including feedback resistors and compensation components close to fb and comp pins. in a multilayer pcb use one layer as a power ground plane and have a control circuit ground (analog ground), to which all signals are referenced. the goal is to localize the high current path to a separate loop that does not interfere with the more sensitive analog control function. these two grounds must be connected together on the pc board layout at a single point. the mlpd is a thermally enhanced package. based on thermal performance it is recommended to use 4-layers pcb. to effectively remove heat from the device the exposed pad should be connected to ground plane using vias. setting the power good threshold power good threshold can be programmed by using two external resistors (r1, r2 in figure 16). the following formulas can be used to set the threshold: where; 0.38v is reference of the internal comparator 0.9*vout is selectable threshold for power good, for this design it is 1.62v. select r 1 =10kohm using (18): r 2 =3.06kohm select r 2 =3.09k use a pull up resistor (4.99k) from pgood pin to vcc. ) --( *r v . *v . v . r out 18 38 0 90 38 0 1 2 ? = 17 = = = = ? = = k r k a a i i m m r limo set onds 65.3 select 65.3 r current) output nominal over (50% 5.37 5.1* 25 95.1 5.1* 3.1 7 ocset )( )( ) --( r i r i i )on(ds ocset ocset )critical (l set 3 ? = = downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 fig.16: application circuit f or IR3629a 12vin to 1.8vout 18 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 pcb metal and components placement ? the lead land width should be equal to the nominal part lead width. the minimum lead to lead spacing should be 0.2mm to minimize shorting. ? the lead land length should be equal to maximum part lead length + 0.3 mm outboard extension + 0.05mm inboard extension. the outboard extension ensures a large and inspectable toe fillet, and the inboard extension will accommodate any part misalignment and ensure a fillet. ? the center pad land length and width should be equal to maximum part pad length and width. however, the minimum metal to metal spacing should be 0.17mm for 2 oz. copper ( 0.1mm for 1 oz. copper and 0.23mm for 3 oz. copper). ? two 0.30mm diameter via should be placed in the center of the pad land and connected to ground to minimize the noise effect on the ic. 19 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 solder resist ? the solder resist should be pulled away from the metal lead lands by a minimum of 0.06mm. the solder resist mis-alignment is a maximum of 0.05mm and it is recommended that the lead lands are all non solder mask defined (nsmd). therefore pu lling the s/r 0.06mm will always ensure nsmd pads. ? the minimum solder resist width is 0.13mm. at the inside corner of the solder resist where the lead land groups meet, it is recommended to provide a fillet so a solder resist width of 0.17mm remains. ? the land pad should be non solder mask defined (nsmd), with a minimum pullback of the solder resist off the copper of 0.06mm to accommodate solder resist mis-alignment. ? ensure that the solder resist in-between the lead lands and the pad land is 0.15mm due to the high aspect ratio of the solder resist strip separating the lead lands from the pad land. ? each via in the land pad should be tented or plugged from bottom boardside with solder resist. 20 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 stencil design ? the stencil apertures for the lead lands should be approximately 80% of the area of the lead lands. reducing the amount of solder deposit ed will minimize the occurrence of lead shorts. since for 0.5mm pitch devices the leads are only 0.25mm wide, the stencil apertures should not be made narrower; openings in stencils < 0.25mm wide are difficult to maintain repeatable solder release. ? the stencil lead land apertures should therefore be shortened in length by 80% and centered on the lead land. ? the land pad aperture should deposit approximately 50% area of solder on the center pad. if too much solder is deposited on the center pad t he part will float and the lead lands will be open. ? the maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. 21 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 (IR3629/IR3629a m) mlpd package 3x4-12lead seating plane leads on 2 sides d e e/2 d2 e2 a (nd-1) x e e l a1 a3 b e d e2 d2 l a a1 m o b s y b a3 l nd n nom inches .008 ref .157 bsc .118 bsc .016 .055 _ min .000 millimeters nom min max .035 .032 .0008 vged-4 0.80 0.90 1.00 0.00 0.02 0.05 1.40 _ 1.80 .0071 0.30 .0096 0.18 0.25 0.20 ref 3.70 3.0 _ .118 4.00 bsc 3.00 bsc 0.40 0.30 0.50 .012 0.50 pitch 6 12 .070 .039 .0019 max .0118 .145 .019 10 .020 pitch 6 e _ terminal 1 identifier tape & reel orientation figure a 22 downloaded from: http:///
IR3629/IR3629a mpbf 11/29/2007 ir world headquarters: 233 kansas st., el segundo, california 90245, usa tel: (310) 252-7105 tac fax: (310) 252-7903 this product has been designed and qualified for the industrial market. visit us at www.irf.com for sales contact information data and specifications subject to change without notice. 11/2007 (IR3629m) mlpd package 3x4-12lead seating plane leads on 2 sides d e e/2 d2 e2 a (nd-1) x e e l a1 a3 b e d e2 d2 l a a1 m o b s y b a3 l nd n nom inches .008 ref .118 bsc .118 bsc .016 .055 _ min .000 millimeters nom min max .035 .032 .0008 veed-5 0.80 0.90 1.00 0.00 0.02 0.05 1.40 _ 1.75 .0071 0.30 .0098 0.18 0.25 0.20 ref 2.70 2.20 _ .087 3.00 bsc 3.00 bsc 0.40 0.30 0.50 .012 0.50 pitch 5 10 .068 .039 .0019 max .0118 .106 .019 10 .020 pitch 5 e _ terminal 1 identifier 1 1 1 tape & reel orientation figure a 23 downloaded from: http:///

▲Up To Search▲

Price & Availability of IR3629

	To Download IR3629 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .